esp_intr_dump() function

The stream to dump to, if NULL then stdout is used

Print information about the card to a stream

Parse and print the CIS information of an SDIO card. using sdmmc_card_init

Dump the list of timers to a stream By default, this function prints the list of active (running) timers. The output format is: | Name | Period | Alarm | - Name — timer pointer - Period — period of timer in microseconds, or 0 for one-shot timer - Alarm - time of the next alarm in microseconds since boot, or 0 if the timer is not started To print the list of all created timers, enable Kconfig option `CONFIG_ESP_TIMER_PROFILING`. In this case, the output format is: | Name | Period | Alarm | Times_armed | Times_trigg | Times_skip | Cb_exec_time | - Name — timer name - Period — same as above - Alarm — same as above - Times_armed — number of times the timer was armed via esp_timer_start_X - Times_triggered - number of times the callback was triggered - Times_skipped - number of times the callback was skipped - Callback_exec_time - total time taken by callback to execute, across all calls

Print a piece of text formatted, which means in a column with a left and a right margin. The lines are wrapped at whitspaces next to right margin. The function does not indent the first line, but only the following ones. Example: arg_print_formatted( fp, 0, 5, "Some text that doesn't fit." ) will result in the following output: Some text that doesn' t fit. Too long lines will be wrapped in the middle of a word. arg_print_formatted( fp, 2, 7, "Some text that doesn't fit." ) will result in the following output: Some text that doesn' t fit. As you see, the first line is not indented. This enables output of lines, which start in a line where output already happened. Author: Uli Fouquet

Print BT CoD minor value

Dump the properties of HID Device to UART

Dump all the previously mapped blocks

Dump ETM channel usages to the given IO stream

Dump IO configuration information to console

Dump the list of all locks to stderr This function dumps debugging information about locks created using esp_pm_lock_create to an output stream. This function must not be called from an ISR. If esp_pm_lock_acquire/release are called while this function is running, inconsistent results may be reported.

Dump the existing VFS FDs data to FILE* fp Dump the FDs in the format: @verbatim -- where: VFS Path Prefix : file prefix used in the esp_vfs_register call FD seen by App : file descriptor returned by the vfs to the application for the path prefix FD seen by driver : file descriptor used by the driver for the same file prefix. @endverbatim

Dump all registered FSs to the provided FILE* Dump the FSs in the format: @verbatim : -> where: index : internal index in the table of registered FSs (the same as returned when registering fd with id) VFS Path Prefix : file prefix used in the esp_vfs_register call or "NULL" VFS entry ptr : pointer to the esp_vfs_fs_ops_t struct used internally when resolving the calls @endverbatim

Dump the sub-sleep power mode enable status

Dumps statistics of all event loops. Dumps event loop info in the format: @verbatim event loop handler handler ... event loop handler handler ... where: event loop format: address,name rx:total_received dr:total_dropped where: address - memory address of the event loop name - name of the event loop, 'none' if no dedicated task total_received - number of successfully posted events total_dropped - number of events unsuccessfully posted due to queue being full handler format: address ev:base,id inv:total_invoked run:total_runtime where: address - address of the handler function base,id - the event specified by event base and ID this handler executes total_invoked - number of times this handler has been invoked total_runtime - total amount of time used for invoking this handler @endverbatim

Dump LDO channel status to the specified stream

Dump the information about time spent in each of the pm modes. Prints three columns: mode name, total time in mode (in microseconds), percentage of time in mode