Symbols
loading...
Files
loading...
SourceVuSTM32 Libraries and SamplesDemonstrations

Demonstrations sample

Demonstrations is a sample project defining the following symbols:

Most used functions

Name
Location
Summary
This function handles NMI exception.
This function handles Hard Fault exception.
This function handles Debug Monitor exception.
This function handles Memory Manage exception.
This function handles Bus Fault exception.
This function handles Usage Fault exception.
This function handles SysTick Handler.
This function handles SVCall exception.
This function handles PendSVC exception.
Main program
This function handles External line 15_10 interrupt request.
Initializes a Drive
I/O control operation
Gets Disk Status
Reads Sector(s)
Writes Sector(s)
Opens a file and copies its content to a buffer.
Open a file and display it on lcd
Compares two buffers.
List up to 25 file on the root directory with extension .BMP
Displays adequate message on TFT available on adafruit 1.8" TFT shield
Copy file BmpName1 to BmpName2
This function is executed in case of error occurrence.
System Clock Configuration The system Clock is configured as follow : System Clock source = PLL (HSI) SYSCLK(Hz) = 100000000 HCLK(Hz) = 100000000 AHB Prescaler = 1 APB1 Prescaler = 2 APB2 Prescaler = 1 HSE Frequency(Hz) = 8000000 PLL_M = 8 PLL_N = 400 PLL_P = 4 PLL_Q = 7 VDD(V) = 3.3 Main regulator output voltage = Scale1 mode Flash Latency(WS) = 3
Displays demonstration menu.
Displays on TFT Images or error messages when error occurred.
SD Card Configuration.
Blinks LED2 with two frequencies depending on User press button.
Check the availability of adafruit 1.8" TFT shield on top of STM32NUCLEO board. This is done by reading the state of IO PC.01 pin (mapped to JoyStick available on adafruit 1.8" TFT shield). If the state of PC.01 is high then the adafruit 1.8" TFT shield is available.

Other commonly used symbols

Name
Location
Summary
Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL). Value of the Internal oscillator in Hz
Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL). Value of the External oscillator in Hz
Miscellaneous Configuration *********************** Vector Table base offset field. This value must be a multiple of 0x200.
@file Demonstrations/Inc/main.h @author MCD Application Team Header for main.c module @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
@file Demonstrations/Inc/stm32f4xx_it.h @author MCD Application Team This file contains the headers of the interrupt handlers. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
External clock source for I2S peripheral This value is used by the I2S HAL module to compute the I2S clock source frequency, this source is inserted directly through I2S_CKIN pad. Value of the External oscillator in Hz
tick interrupt priority
Internal Low Speed oscillator (LSI) value. LSI Typical Value in Hz
External Low Speed oscillator (LSE) value. Value of the External Low Speed oscillator in Hz
Time out for HSE start up, in ms
Time out for LSE start up, in ms
@file stm32f4xx_hal_conf.h @author MCD Application Team HAL configuration file. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
This is the list of modules to be used in the HAL driver
This is the HAL system configuration section Value of VDD in mv
Transceiver Basic Control Register
Auto-Negotiation process completed
PHY special control/ status register Offset
Transceiver Basic Status Register
PHY Speed mask
Enable auto-negotiation function
PHY Duplex mask
Select the power down mode
Valid link established
PHY Reset
Select loop-back mode
Set the full-duplex mode at 100 Mb/s
Set the half-duplex mode at 100 Mb/s
Set the full-duplex mode at 10 Mb/s
Set the half-duplex mode at 10 Mb/s
Restart auto-negotiation function
Isolate PHY from MII
Jabber condition detected
Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code
Portions COPYRIGHT 2017 STMicroelectronics Copyright (C) 2017, ChaN, all right reserved. Copyright (c) 2017 STMicroelectronics. All rights reserved. This software component is licensed by ST under Ultimate Liberty license SLA0044, the "License"; You may not use this file except in compliance with the License. You may obtain a copy of the License at: www.st.com/SLA0044
PHY Interrupt Source Flag register Offset
PHY Link down inturrupt
@file sd_diskio.h @author MCD Application Team Header for sd_diskio.c module. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
@file fatfs_storage.h @author MCD Application Team This file contains all the functions prototypes for the storage firmware driver. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.

Dependencies