Symbols
loading...
Files
loading...
SourceVuSTM32 Libraries and SamplesFreeRTOS_Queues

FreeRTOS_Queues sample

FreeRTOS_Queues is a sample project defining the following symbols:

Most used functions

Name
Location
Summary
This function handles NMI exception.
This function handles Hard Fault exception.
This function handles Debug Monitor exception.
This function handles Memory Manage exception.
This function handles Bus Fault exception.
This function handles Usage Fault exception.
This function handles SysTick Handler.
Main program
This function handles TIM interrupt request.
Message Queue Producer Thread.
Message Queue Consumer Thread.
System Clock Configuration The system Clock is configured as follow : System Clock source = PLL (HSE) SYSCLK(Hz) = 100000000 HCLK(Hz) = 100000000 AHB Prescaler = 1 APB1 Prescaler = 2 APB2 Prescaler = 1 HSE Frequency(Hz) = 8000000 PLL_M = 8 PLL_N = 200 PLL_P = 2 PLL_Q = 7 PLL_R = 2 VDD(V) = 3.3 Main regulator output voltage = Scale1 mode Flash Latency(WS) = 3

Other commonly used symbols

Name
Location
Summary
Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL). Value of the Internal oscillator in Hz
Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL). Value of the External oscillator in Hz
Miscellaneous Configuration *********************** Vector Table base offset field. This value must be a multiple of 0x200.
@file FreeRTOS/FreeRTOS_Queues/Inc/main.h @author MCD Application Team This file contains all the functions prototypes for the main.c file. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
@file FreeRTOS/FreeRTOS_Queues/Inc/stm32f4xx_it.h @author MCD Application Team This file contains the headers of the interrupt handlers. Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); You may not use this file except in compliance with the License. You may obtain a copy of the License at: http://www.st.com/software_license_agreement_liberty_v2 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.
Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code
External clock source for I2S peripheral This value is used by the I2S HAL module to compute the I2S clock source frequency, this source is inserted directly through I2S_CKIN pad. Value of the external oscillator in Hz
tick interrupt priority
Internal Low Speed oscillator (LSI) value. LSI Typical Value in Hz
External Low Speed oscillator (LSE) value. Value of the External Low Speed oscillator in Hz
Time out for HSE start up, in ms
Time out for LSE start up, in ms
@file stm32f4xx_hal_conf.h @author MCD Application Team HAL configuration file. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
This is the list of modules to be used in the HAL driver
This is the HAL system configuration section Value of VDD in mv

Dependencies