Symbols
loading...
Files
loading...
SourceVuSTM32 Libraries and SamplesCDC_Standalone

CDC_Standalone sample

CDC_Standalone is a sample project defining the following symbols:

Most used functions

Name
Location
Summary
This function handles NMI exception.
This function handles Hard Fault exception.
This function handles Debug Monitor exception.
This function handles Memory Manage exception.
This function handles Bus Fault exception.
This function handles Usage Fault exception.
This function handles SysTick Handler.
This function handles SVCall exception.
This function handles PendSVC exception.
Main program
This function handles External line 15_10 interrupt request.
Initializes a Drive
I/O control operation
Gets Disk Status
Reads Sector(s)
Writes Sector(s)
This function handles DMA2 Stream 3 interrupt request.
This function handles DMA2 Stream 6 interrupt request.
This function handles SDIO interrupt request.
Demo state machine.
This function handles External line 2 interrupt request.
Manages the menu on the screen.
Changes the selection mode.
Clears the text zone.
Initializes the SD Storage.
Copies disk content in the explorer list.
Manages CDC Menu Process.
Manages the setting menu on the screen.
Handles CDC Receive Menu.
Handles CDC Send Menu.
Shows files on the root.
Handles Configuration Menu.
Returns default configuration.
Probes the CDC Settings joystick state.
Adjusts CDC configuration setting Menu.
Probes the CDC joystick state.
Returns from Configuration Menu.
Displays received data
Initializes Configuration Menu.
Sets the CDC demo initial values.
Returns from Receive Menu
Demo_Application Demo state machine
Returns from Send Menu
Sends file to the root.
CDC application Init.
User Process
System Clock Configuration The system Clock is configured as follow : System Clock source = PLL (HSE) SYSCLK(Hz) = 168000000 HCLK(Hz) = 168000000 AHB Prescaler = 1 APB1 Prescaler = 4 APB2 Prescaler = 2 HSE Frequency(Hz) = 25000000 PLL_M = 25 PLL_N = 336 PLL_P = 2 PLL_Q = 7 VDD(V) = 3.3 Main regulator output voltage = Scale1 mode Flash Latency(WS) = 5
Probes the CDC joystick state.

Other commonly used symbols

Name
Location
Summary
Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL). Value of the Internal oscillator in Hz
Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL). Value of the External oscillator in Hz
@file USB_Host/CDC_Standalone/Src/main.h @author MCD Application Team Header for main.c module @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
@file USB_Host/CDC_Standalone/Src/stm32f4xx_it.h @author MCD Application Team This file contains the headers of the interrupt handlers. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
External clock source for I2S peripheral This value is used by the I2S HAL module to compute the I2S clock source frequency, this source is inserted directly through I2S_CKIN pad. Value of the external oscillator in Hz
tick interrupt priority
Internal Low Speed oscillator (LSI) value.
External Low Speed oscillator (LSE) value. Value of the External Low Speed oscillator in Hz
Time out for HSE start up, in ms
Time out for LSE start up, in ms
@file stm32f4xx_hal_conf.h @author MCD Application Team HAL configuration file. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
This is the list of modules to be used in the HAL driver
This is the HAL system configuration section Value of VDD in mv
Transceiver Basic Control Register
Auto-Negotiation process completed
PHY status register Offset
Transceiver Basic Status Register
PHY Speed mask
Enable auto-negotiation function
PHY Duplex mask
Select the power down mode
Valid link established
PHY Reset
Select loop-back mode
Set the full-duplex mode at 100 Mb/s
Set the half-duplex mode at 100 Mb/s
Set the full-duplex mode at 10 Mb/s
Set the half-duplex mode at 10 Mb/s
Restart auto-negotiation function
Isolate PHY from MII
Jabber condition detected
Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code
MII Interrupt Status and Misc. Control Register
MII Interrupt Control Register
PHY Link mask
PHY Enable interrupts
PHY Enable output interrupt events
Enable Interrupt on change of link status
PHY link status interrupt mask
This is the list of modules to be used in the HAL driver
Portions COPYRIGHT 2017 STMicroelectronics Copyright (C) 2017, ChaN, all right reserved. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
@file USB_Host/CDC_Standalone/Inc/usbh_conf.h @author MCD Application Team General low level driver configuration @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
@file USB_Host/CDC_Standalone/Src/lcd_log_conf.h @author MCD Application Team LCD Log configuration file. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
@file sd_diskio.h @author MCD Application Team Header for sd_diskio.c module. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.

Dependencies