Symbols
loading...
Files
loading...
SourceVuSTM32 Libraries and SamplesFx_Dual_Instance

Fx_Dual_Instance sample

Fx_Dual_Instance is a sample project defining the following symbols:

Most used functions

Name
Location
Summary
This function handles Non maskable interrupt.
This function handles Hard fault interrupt.
This function handles Debug monitor.
This function handles Memory management fault.
This function handles Pre-fetch fault, memory access fault.
This function handles Undefined instruction or illegal state.
This function is executed in case of error occurrence.
The application entry point.
System Clock Configuration
This function handles TIM6 global interrupt, DAC1 and DAC2 underrun error interrupts.
This function handles DMA2 stream3 global interrupt.
This function handles DMA2 stream6 global interrupt.
This function handles SDIO global interrupt.
Application ThreadX Initialization.
MX_ThreadX_Init
Application FileX Initialization.
SDIO Initialization Function
Retargets the C library printf function to the USART.
Read Data from the SD device into a buffer.
Write data buffer into the SD device.
Initializes the SD IP instance
Deinitializes the SD IP instance
Check the SD IP status.
QUADSPI Initialization Function
Send a Write Enable command and wait it is effective.
Read the SR of the memory and wait the EOP.
Get the status of the QSPI instance
Get size info of the flash meomory
Read data from the QSPI memory into a buffer
write a data buffer into the QSPI memory
Erase the whole flash or a single block
Check that a block was actually erased
Initializes the QSPI IP instance
USART3 Initialization Function
Enable DMA controller clock
GPIO Initialization Function
Reset the QSPI memory.
Configure the dummy cycles on memory side.

Other commonly used symbols

Name
Location
Summary
Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL). Value of the Internal oscillator in Hz
Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL). Value of the External oscillator in Hz
@file : main.h : Header for main.c file. This file contains the common defines of the application. @attention Copyright (c) 2021 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
@file stm32f4xx_it.h This file contains the headers of the interrupt handlers. @attention Copyright (c) 2021 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
External clock source for I2S peripheral This value is used by the I2S HAL module to compute the I2S clock source frequency, this source is inserted directly through I2S_CKIN pad. Value of the External audio frequency in Hz
tick interrupt priority
Internal Low Speed oscillator (LSI) value. LSI Typical Value in Hz
External Low Speed oscillator (LSE) value. Value of the External Low Speed oscillator in Hz
Time out for HSE start up, in ms
Time out for LSE start up, in ms
@file stm32f4xx_hal_conf_template.h @author MCD Application Team HAL configuration template file. This file should be copied to the application folder and renamed to stm32f4xx_hal_conf.h. @attention Copyright (c) 2017 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
This is the list of modules to be used in the HAL driver
This is the HAL system configuration section Value of VDD in mv
Transceiver Basic Control Register
Auto-Negotiation process completed
PHY status register Offset
Transceiver Basic Status Register
PHY Speed mask
Enable auto-negotiation function
PHY Duplex mask
Select the power down mode
Valid link established
PHY Reset
Select loop-back mode
Set the full-duplex mode at 100 Mb/s
Set the half-duplex mode at 100 Mb/s
Set the full-duplex mode at 10 Mb/s
Set the half-duplex mode at 10 Mb/s
Restart auto-negotiation function
Isolate PHY from MII
Jabber condition detected
Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code
ThreadX Component User Specific
@file app_threadx.h @author MCD Application Team ThreadX applicative header file @attention Copyright (c) 2021 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
@file app_azure_rtos.h @author MCD Application Team azure_rtos application header file @attention Copyright (c) 2021 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
@file app_azure_rtos_config.h @author MCD Application Team azure_rtos config header file @attention Copyright (c) 2021 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
@file app_filex.h @author MCD Application Team FileX applicative header file @attention Copyright (c) 2021 STMicroelectronics. All rights reserved. This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
FileX Component User Specific
LevelX Component User Specific

Dependencies